android:g1使用openvpn
Table of Contents
如何在G1上使用OpenVPN
本方讲述了如何在G1上使用OpenVPN,前提是你用的Rom已经安装了OpenVPN.
使用命令:
openvpn --config client.conf -auth auth
说明:
1.将证书文件放到/data/vpn目录下
2.手动编辑一个auth文件:第一行写证书用户名,第二行写密码,也放到/data/vpn目录下
3.cd 到/data/vpn目录下
4.启动OpenVPN
openvpn --config client.conf -auth auth
如果嫌每次输入这个命令,可以弄一个小脚本,将这行命令扔到一个文件里,比如:
echo "openvpn --config client.conf -auth auth" >>vpn chmod 777 vpn ./vpn
就可以启动OpenVPN了
5.如果一切正常,可以查看下G1的IP:
# busybox ifconfig
busybox ifconfig
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:460 errors:0 dropped:0 overruns:0 frame:0
TX packets:460 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:34332 (33.5 KiB) TX bytes:34332 (33.5 KiB)
rmnet0 Link encap:Ethernet HWaddr 7A:ED:9A:75:46:FC
inet addr:10.110.219.120 Bcast:10.110.219.123 Mask:255.255.255.252
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:2722 errors:0 dropped:0 overruns:0 frame:0
TX packets:2330 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:2344247 (2.2 MiB) TX bytes:289966 (283.1 KiB)
tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
inet addr:10.8.0.18 P-t-P:10.8.0.17 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1
RX packets:7 errors:0 dropped:0 overruns:0 frame:0
TX packets:41 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:404 (404.0 B) TX bytes:4931 (4.8 KiB)
其中tun0就是OpenVPN链接了:
tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
inet addr:10.8.0.18 P-t-P:10.8.0.17 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1
RX packets:7 errors:0 dropped:0 overruns:0 frame:0
TX packets:41 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:404 (404.0 B) TX bytes:4931 (4.8 KiB)
/var/www/dokuwiki/wiki/data/pages/android/g1使用openvpn.txt · Last modified: 2016/05/05 13:07 by 127.0.0.1